VialDose

Reverse Reconstitution Calculator

Most calculators start from the water you already added. This one starts from where you want to end up: pick the syringe mark your dose should sit on, and get the exact water volume for your vial.

Quick answer: water (mL) = vial contents ÷ (dose ÷ mark in mL). A 5 mg vial with 2 mL of BAC water is 2.5 mg/mL, so a 250 mcg dose sits on a 10-unit mark of a U-100 syringe. Want a different mark — say 5 units for the same dose? Add 1 mL instead. Enter your numbers below and the exact volume appears instantly, computed in your browser.
Unit conversion only — the dose comes from your prescriber, never from us. Nothing you type leaves your browser. IU is never mixed with mass units.

Why work backwards from a mark?

Every dose should be easy to read at a glance. If your draw lands between graduation lines, every injection invites a small reading error — and the error repeats. Working backwards fixes that: you choose a whole mark (5, 10, 20 units), and the calculator tells you the water volume that puts your dose exactly on it.

The trade-off is readability versus volume. More water spreads the dose over a bigger draw, which is easier to read but uses more of the syringe. Less water concentrates the solution, which makes tiny draws that are hard to measure. A draw below about 3 units is where accuracy starts to suffer — if your draw would be under 3 units, add more water.

How the math works

concentration needed = dose ÷ mark (in mL)
water to add = vial contents ÷ concentration needed

Example with round numbers: you want a 250 mcg dose to sit on a 10-unit mark of a U-100 syringe. Ten units is 0.1 mL, so the concentration must be 250 ÷ 0.1 = 2,500 mcg/mL. A 5 mg vial ÷ 2,500 mcg/mL = 2 mL of water. Change the mark to 5 units and the answer becomes 1 mL; change it to 20 units and it becomes 4 mL. Same vial, same dose — only the water changes.

Common vial and water combinations

Reference concentrations for common vial sizes — arithmetic only, not suggestions:

VialWaterConcentration250 mcg reads as
5 mg1 mL5 mg/mL5 units (U-100)
5 mg2 mL2.5 mg/mL10 units
5 mg5 mL1 mg/mL25 units
10 mg2 mL5 mg/mL5 units
10 mg4 mL2.5 mg/mL10 units
2 mg1 mL2 mg/mL12.5 units
10 mg1 mL10 mg/mL2.5 units

Notice the pattern: doubling the water halves the concentration and doubles the draw. The vial's contents never change — the diluent guide covers why bacteriostatic water (0.9% benzyl alcohol) is the common multi-use choice and how much it can carry.

From concentration instead

If your protocol names a concentration rather than a mark — say "1 mg/mL" — use the second mode. Water = vial ÷ target concentration. A 10 mg vial at 1 mg/mL takes 10 mL; the same vial at 2 mg/mL takes 5 mL. If the answer is over about 5 mL, check whether the vial can physically hold it; if it is under 0.1 mL, the concentration is likely a typo.

Have the water already added?
The main calculator goes the other way: vial, water and dose in — units out.
Open the main calculator

FAQ

How do I calculate how much bacteriostatic water to add?
Divide the vial contents by the concentration you want. A 5 mg vial at 1 mg/mL takes 5 mL. To work from a syringe mark instead, use the first mode above: it solves for the water that puts your dose exactly on the mark you picked.
How much BAC water should I add to a 5 mg vial?
That depends on the draw you want. With 2 mL, a 250 mcg dose is a 10-unit draw — easy to read. With 1 mL it is 5 units. More water = larger, easier draw. The dose itself comes from your prescriber; the water only decides where it lands on the syringe.
Why should my dose land on a whole mark?
Reading between graduation lines invites small, repeating errors. A draw on a printed mark can be verified at a glance every time.
Does adding more water change the dose?
No. The total peptide in the vial never changes — water only sets the concentration, and therefore the volume each dose takes up.
Can it convert IU to mg?
No. IU and mass units measure different things. Same-unit entries only — mixed entries are blocked with an explanation, in this tool and everywhere on VialDose.
Do you store my numbers?
No. Everything is computed locally in your browser. No account, no server round-trip.

Guides

VialDose for iOS & Android
The calculator, plus a dose log, smart site rotation, vial inventory and reminders — private by design.
Download on the App Store — free Get it on Google Play — free
VialDose is not a medical device and does not diagnose, treat, cure, or prevent any medical condition. This tool performs unit conversions only. Always consult a healthcare professional before starting or changing any medication or protocol.